立式振動電機要想使用的壽命更長，在使用時要注意一下幾點：
1、檢查立式振動電機傳動機構的工作是否可靠。
2、檢查電機的外表有無裂紋，各緊固螺釘及零件是否齊全，惦記的固定情況是否良好。
3、根據銘牌所示數據，如電壓、功率、頻率、聯結、轉速等與電源、負載比較是否相符。
4、檢查立式振動電機的通風情況及軸承潤滑情況是否正常。
5、新的或長期停用的電機，使用前應檢查繞組間和繞組對地絕緣電阻。通常對500V以下的電機用500V絕緣電阻表；對500-1000V的電機用1000V絕緣電阻表；對1000V以上的電機用2500V絕緣電阻表。絕緣電阻每千伏工作電壓不得小于1MΩ，并應在電機冷卻狀態下測量。
6、扳動電機轉軸，檢查轉子能否自由轉動，轉動時有無雜聲。
7、檢查電機的電刷裝配情況及舉刷機構是否靈活，舉刷手柄的位置是否正確。
8、檢修中調整激振塊時，要注意其對稱性，使激振塊兩兩相對，即兩端激振塊的中心連接線要與轉軸平行。
9、避免振動電機垂直或傾斜安裝，減少因電機兩端軸承受激振塊重力影響產生的損壞；
Vertical vibration motor to use longer, when use must pay attention the following points:1, check the vibration motor transmission's work is reliable.2, check the motor appearance has no cracks, the fastening screws and parts are complete, the fixation is good.In 3, according to the nameplate shows data, such as voltage, power, frequency, coupling, rotating speed and power, comparing the load line.4, check that the vibration motor ventilation and bearing lubrication is normal.5, new or long-term disabling motor should be checked before use, winding and winding insulation resistance against ground. Usually the 500V following the motor insulation resistance meter for 500V; on 500-1000V motor using 1000V insulation resistance meter; the above 1000V motors with 2500V insulation resistance meter. Insulation resistance per kilovolt voltage shall not be less than 1MΩ, and should be in the motor cooling state measurement.In 6, a motor shaft, check whether the free rotation of rotor, rotating when there is no noise.7, check the motor brush assembly and brush lifting mechanism is flexible, brush lifting handle position is correct.8, maintenance of adjustment of excitation block, attention should be paid to its symmetry, so that the vibration block two two relative ends, namely excitation block the line connecting the centers of rotation parallel to and.9, avoid the vibration motor vertical or inclined installation, reduced due to the two ends of the motor shaft bearing vibration block gravity impact damage;
